|
HBA's & Switches
Emulex HBA's
 Sunstar Company
is proud to be an Emulex partner!
LP982 2Gb/s Fibre Channel PCI-X Host Bus
Adapter
 |
Major Features
- full duplex 2Gb/s Fibre Channel delivering up to 400MB/s
- automatic speed negotiation
- automatic topology detection
- full fabric support using F_Port and FL_port connections
- onboard hardware context cache for superior fabric performance
- support for use of multiple concurrent protocols (SCSI and IP)
- full support for both FC service class 2 and 3
- full fabric boot support in x86 environments to multiple LUNs
- support for FC-Tape (FCP-2) devices
- 66/100/133MHz PCI-X 1.0a and PCI 2.2 compatibility
- end-to-end parity protection for high data integrity
- robust suite of software supporting Windows 2000, Windows NT,
Linux and NetWare
- optical small form factor (LC) interface
|
|
Description The LP982 PCI-X host bus adapter offers a highly
integrated 2Gb/s Fibre Channel HBA for use in servers based on either
PCI or the latest PCI-X expansion bus. The LP982 delivers exceptional
performance through the use of an Emulex Pegasus ASIC, a 266MIPs onboard
processor, an embed-ded 1Gig/2Gig SERDES, and a high performance unified
QDR SRAM. The LP982 features automatic topology detection and automatic
speed negotiation capability. These capabilities allow complete
compatibility with existing 1Gb/s Fibre Channel SANs, while allowing
seamless upgrades to higher speed 2Gb/s SANs.
The features of this PCI-X based HBA provide the flexibility and
broad interoperability needed for complex, highly scalable SANs. The
LP982 provides a combination of features, including switched fabric
support using F_Port and FL_Port connections, full-duplex data
transfers, high data integrity features, support for all Fibre Channel
topologies, and support for service classes 2 and 3.
The LP982 also features sophisticated hardware that provides superior
performance in SANs and provides best in class server CPU offload. This
exclu-sive hardware delivers low latency and high throughput in switched
fabric, arbitrated loop and clustered environments. Support for fiber
optic cabling is provided through an embedded small form factor (LC)
optical interface.
Driver Support
A rich suite of software complements the LP982. Some examples of the
features included are, LUN Masking, LUN Mapping, Persistent Binding, I/O
Coalescing, full fabric boot as well as support for multi or
simul-taneous protocol (SCSI & IP) operation. In addition, most drivers
include a full-featured implementation of the FC-MI HBA Management
Interface. These features enable advanced storage area network (SAN)
implementations in Windows 2000, Windows NT, Linux, and NetWare
environments. All drivers are also fully compatible with the Emulex
LP9002L, LP850, LP8000, LP7000E, LP952L, LP9402DC, LP9002C and LP9802
host bus adapters.
|
|
|
standards
ANSI Fibre Channel FC-FS
ANSI Fibre Channel FC-PH
ANSI Fibre Channel FC-PI
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-MI
ANSI Fibre Channel FC-FLA
PCI-X 1.0a
PCI local bus revision 2.2 (see power requirements)
Fibre Channel Class 2, 3
PHP hot plug - hot swap
architecture
Emulex Pegasus ASIC
technology
up to 133MHz PCI-X DMA
2Gb/s or 1Gb/s FC Link
2MB FLASH memory
1MB QDR SRAM
software environments
Windows 2000
Windows NT
Linux
NetWare
hardware environments
x86, PCI hardware
platforms
3.3V signaling, 5V tolerant
32/64b 33/66MHz PCI
66/100/133MHz PCI-X
optical
|
data
rate: |
1.0625/2.125Gb/s |
|
optics: |
short
wave laser |
|
cable: |
50/125µm multi-mode fiber |
| |
62.5/125µm multi-mode fiber |
|
connector: |
LC |
|
distance: |
(1Gb/s) |
| |
500
meters (1,640') 50/125 µm fiber |
| |
300
meters (984') 62.5/125 µm fiber |
| |
(2Gb/s) |
| |
300
meters (984') 50/125 µm fiber |
| |
150
meters (492') 62.5/125 µm fiber |
|
physical dimensions
short low profile MD2
form factor
low profile or standard bracket
167.64mm x 64.42mm (6.60" x 2.54")
power requirements
|
volts: |
+3.3
VDC (± 5%) |
|
power: |
7.7
watts @ 66MHz, 8.5 watts @ 133MHz (typ) |
environmental conditions
|
operating temperature: |
0° to
45°C (32° to 113°F) |
|
airflow required: |
100
lf/m |
storage temperature
-40° to 70°C (-40° to
158°F)
relative humidity
5% to 95%
non-condensing
agency approvals
Class 1 Laser Product
per DHHS 21CFR (J) & EN60825
UL recognized to UL 1950
CUR recognized to CSA22.2, No. 950
TUV certified to EN60950
FCC rules, Part 15, Class A
ICES–003, Class A
EMC Directive 89/336/EEC (CE Mark)
EN55022, Class A
EN55024
Australian EMC Framework (C–Tick Mark)
AS/NZS 3548, Class A
VCCI, Class A
ordering information
|
LP982–F2 |
embedded multi-mode optic interface (LC) |
|
|
|
