|
HBA's & Switches
Emulex HBA's
 Sunstar Company
is proud to be an Emulex partner!
LP850 LightPulse 1Gb/s Fibre
Channel PCI Host
Bus Adapter
 |
Major
Features
- simultaneous full duplex 1Gb/s Fibre Channel delivers up to
200MB/s
- full fabric support using F_Port and FL_Port connections
- onboard hardware context cache for superior fabric performance
- support for concurrent use of multiple protocols (SCSI & IP)
- full support for FC service Class 2 and 3
- support for FC-Tape (FCP-2) devices
- 64 bit, 33MHz PCI
- end-to-end parity protection for high data integrity
- robust suite of software including IP and storage protocols under
Windows 2000, Windows NT, Linux and NetWare
|
|
Description The LightPulse™ LP850 Fibre
Channel PCI host bus adapters deliver exceptional performance through
the use of Emulex’s Dragonfly ASIC, a 266MIPS onboard processor and high
speed buffer memory. The LP850 features a 64 bit PCI interface and
provides the richest feature set available.
The LP850 provides high-performance Fibre Channel connectivity for
entry-level Windows 2000, Windows NT, Linux and NetWare systems. Based
on the Emulex LP8000 architecture, the LP850 provides a unique
combination of features, including switched fabric support using F_Port
and FL_Port connections, full-duplex data transfers, high data integrity
features, support for all Fibre Channel topologies and support for
service class 2 and 3.
The LP850 also features sophisticated hardware that provides superior
performance in storage area networks, delivering low latency and high
throughput in switched, arbitrated loop and clustered environments.
Driver Support |
The LightPulse™ LP850 is complemented by a rich suite of software
support including storage protocol (SCSI), network protocol (IP) as well
as concurrent multi–protocol (SCSI & IP) operation, enabling advanced
storage area network (SAN) implementations in Windows 2000, Windows NT,
Linux and NetWare environments. All drivers are also fully compatible
with the Emulex LP9002L, LP9000, LP8000, LP7000E and LP952L host bus
adapters.
|
|
standards
ANSI Fibre Channel FC-PH
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
PCI local bus revision 2.2
Fibre Channel Class 2, 3
PHP hot plug - hot swap
gigabit interface converter (GBIC)
architecture
Emulex Dragonfly ASIC
technology
up to 33MHz PCI bus master DMA
512KB FLASH memory
1MB code RAM
128KB buffer RAM
software environments
Windows 2000
Windows NT
Linux
NetWare
hardware environments
x86 PCI hardware platforms
3.3V signaling, 5V tolerant
copper
| data rate: |
1.0625 Gb/s |
| cable type: |
Dual Twinax or
Quad Axial |
| connector type: |
DB9 |
| distance: |
30 meters (98') |
optical
| data rates: |
1.0625 Gb/s |
| optics: |
short wave lasers |
| cable: |
50/125 µm
multi-mode fiber |
| |
62.5/125 µm
multi-mode fiber |
| connector type: |
dual SC |
| distance: |
500 meters
(1640') 50/125 µm fiber |
| |
300 meters (984')
62.5/125 µm fiber |
|
physical dimensions
short PCI form factor
174.75mm x 106.68mm
(6.88" X 4.20")
power requirements
| volts: |
+5 VDC +/- 5% |
| power: |
10 watts typical |
environmental conditions
| operating
temperature: |
0° to 45° C (32°
to 113° F) |
| storage
temperature: |
-10° to 55° C
(14° to 131°F ) |
| relative
humidity: |
5% to 95%
non-condensing |
agency approvals
Class 1 Laser Product per DHHS
21CFR (J) & EN60825
UL recognized to UL 1950
CUR recognized to CSA22.2, No. 950
TUV certified to EN60950
FCC rules, Part 15, Class B*
ICES–003, Class B*
EMC Directive 89/336/EEC (CE Mark)
EN55022, Class B*
EN55024
Australian EMC Framework (C–Tick Mark)
eAS/NZS 3548, Class B*
VCCI, Class B*
ordering information
|
LP850-F1 |
embedded multi-mode optic interface |
|
|
|
|
